OWNER’S
INSTRUCTIONS
Indoor unit
Outdoor unit
AQ07S8GE
AQ07SBGE
SH07ZS8
UQ07S8GE
UQ07SBGE
SH07ZS8X
UQ09S8GE
UQ09SBGE
SH09ZS8X
UQ12SBGE
UQ12SGGB
UQ12SGGE
SH12ZSGX
UQ18S0GB
UQ18S0GE
SH18ZS0X
UQ24S6GB
UQT24S6GE
SH24TS6X
AQ09S8GE
AQ09SBGE
SH09ZS8
AQ12SBGE
AQ12SGGB
AQ12SGGE
SH12ZSG
AQ18S0GB
AQ18S0GE
SH18ZS0
AQ24S6GB
AQT24S6GE
SH24TS6
SPLIT TYPE ROOM AIR CONDITIONER
( Cool and Heat )
E DB98-08237A(5)
Contents
◆
◆
PREPARING YOUR AIR CONDITIONER
◆◆◆Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
◆◆◆View of the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
◆◆◆Remote Control-Buttons and Display . . . . . . . . . . . . . . . . . . . . . .
◆◆◆Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
◆◆◆Inserting the Remote Control Batteries . . . . . . . . . . . . . . . . . . . . .
2
4
6
7
8
OPERATING YOUR AIR CONDITIONER
◆◆◆Selecting the Automatic Operating Mode . . . . . . . . . . . . . . . . . . .
9
◆◆◆Cooling Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
◆◆◆Heating Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
◆◆◆Changing the Room Temperature Quickly . . . . . . . . . . . . . . . . . . 12
◆◆◆Removing Excess Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
◆◆◆Airing Your Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
◆◆◆Selecting Energy Saving Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
◆◆◆Adjusting the Air Flow Direction Vertically . . . . . . . . . . . . . . . . . . . 16
◆◆◆Adjusting the Air Flow Direction Horizontally . . . . . . . . . . . . . . . . 17
◆
◆
PROGRAMMING YOUR AIR CONDITIONER
◆◆◆Setting the On Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
◆◆◆Setting the Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
◆◆◆Setting the Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
RECOMMENDATIONS FOR USE
◆◆◆Operating Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
◆◆◆Temperature and Humidity Ranges . . . . . . . . . . . . . . . . . . . . . . . . 22
◆◆◆Operating Your Air Conditioner Without the Remote Control . . . . . 22
◆◆◆Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
◆◆◆Cleaning Your Air Conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
◆◆◆Cleaning Deodorizing and Bio-Green filters (option) . . . . . . . . . . . 24
◆
TECHNICAL SPECIFICATIONS
E-3
View of the Unit
The design and shape are subject to change according to the model.
Indoor Unit
On/Off switch
Air filter
(under the grille)
Air Inlet
Remote Control Sensor
Air flow blades
(outlet)
TURBO indicator (RED)
Energy Saving indicator
(GREEN)
Operation indicator
(Cooling-GREEN,
Heating-RED)
Timer indicator
(YELLOW)
E-4
Outdoor Unit
UQ07S8GE
Air Outlet
SH07ZS8X
UQ09S8GE
SH09ZS8X
Air Inlet(Rear)
SH30ZC1(C2)X
Connection Valve
(inside)
Outdoor Unit
Outdoor Unit
Outdoor Unit
UQ07SBGE UQ09SBGE UQ12SBGE
Air Inlet(Rear)
Air Outlet
Connection Valve
UQ12SGGB UQ12SGGE SH12ZSGX
Air Inlet(Rear)
Air Outlet
Connection Valve
(inside)
UQ18S0GB
UQ24S6GB
UQ18S0GE
UQT24S6GE SH24TS6X
SH18ZS0X
Air Inlet(Rear)
Air Outlet
Connection Valve
E-5
Remote Control - Buttons and Display
Remote control
transmission indicator
Mode selection button
(AUTO, COOL, DRY, FAN, HEAT)
Operating mode
(
AUTO,
COOL,
DRY,
FAN,
HEAT)
Temperature adjustment
buttons
Temperature setting
Turbo mode
Sleep mode
Turbo/Sleep mode
selection button
Energy saving
Fan speed
Fan speed adjustment button
Swing button
Air flow direction
On Timer setting
On Timer button
Off Timer button
Off Timer setting
Battery discharge indicator
On/Off &
Timer Set/Cancel button
Energy Saving button
E-6
Getting Started
You have just purchased a split type air conditioner and it has been
installed by your installation specialist.
Your Owner’s Instructions contains valuable information on using your
air conditioner. Please take the time to read it as it will help you take full
advantage of the unit’s features.
The booklet is organized as follows.
◆ The following figures are shown on pages from 4 to 6 :
-
-
Indoor and outdoor units
Remote control(buttons and display)
They will help you find the buttons and understand the symbols displayed.
◆ In the main part of the installation book, you will find a series of
step-by-step procedures for each function available.
The illustrations in the step-by-step procedures use three different symbols:
PRESS
PUSH
HOLD DOWN
E-7
Inserting the Remote Control Batteries
You must insert or replace the remote control batteries when :
◆ You purchase the air conditioner
◆ The remote control does not work correctly
Note
◆ Use two AAA, LR03 1.5V batteries.
◆ Do not use old batteries or different kinds of batteries together.
◆ Batteries may be completely discharged after 12 months, even
◆ if they have not actually been used.
1
2
Push the battery cover on the rear of the remote control with your thumb
in the direction of the arrow and remove it.
Insert the two batteries, taking care to respect the polarities :
◆ + on the battery with + on the remote control.
◆ - on the battery with - on the remote control.
3
Close the cover by sliding it back until it clicks into place.
E-8
Selecting the Automatic Operating Mode
You can start the air conditioner in Automatic mode from your remote
control. In the Automatic mode, the standard temperature and the
optimum fan speed is selected automatically. You can adjust the
standard temperature but not the fan speed.
1
If necessary, press the
(On/Off) button.
Result:
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
lt will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control,
press the
appears.
button on the remote control one or more times until it
Result:
◆ The indoor unit beeps each time you press the
button.
◆ The air conditioner runs in AUTO mode.
Note
You can change modes at any time.
3
To adjust the standard temperature (The air conditioner automatically
set the standard temperature by the current room temperature.),
press the
button one or more times.
SET TEMP. SET TEMP.
-2°C -1°C
< When you feel hot >
-
SET TEMP. SET TEMP.
+1°C +2°C
< When you feel chilly >
Standard temperature
E-9
Cooling Your Room
You must select the Cool mode if you wish to adjust the:
◆ Cooling temperature
◆ Fan speed when cooling
1
If necessary, press the
(On/Off) button.
Result: The operation indicator on the indoor unit lights up.
◆
◆ The air conditioner starts up in the mode selected
when the unit was last used.
◆ The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism to
prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
lt will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control,
press the
appears.
button on the remote control one or more times until it
Result:
◆
◆
The indoor unit beeps each time you press the
The air conditioner runs in COOL mode.
button.
Note
You can change modes at any time.
3
To adjust the temperature, press the
the required temperature is displayed.
button one or more times until
Possible temperatures are between 18°C and 30°C inclusive.
Result: Each time you press the button:
◆
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts cooling, provided that the room
temperature is higher than the selected temperature.
◆ If the room temperature reaches the set temperature, the air
conditioner stops cooling, but the fan is still operating.
4
Select the fan speed by pressing the
until the required setting is displayed:
button one or more times
)
Automatic (rotated :
Low
Medium
High
Result:
Each time you press the
beeps.
button, the indoor unit
5
To control the direction of the air flow, refer to pages 16 and 17.
E-10
Heating Your Room
You must select the Heat mode if you wish to adjust the:
◆ Heating temperature
◆ Fan speed when heating
1
If necessary, press the
(On/Off) button.
Result: The operation indicator on the indoor unit lights up.
◆
◆ The air conditioner starts up in the mode selected when
the unit was last used.
◆ The indoor unit beeps.
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
IMPORTANT
◆ Plugged in
◆ Stopped
It will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control, press the
button on the remote control one or more times until it appears.
Result:
◆
◆
The indoor unit beeps each time you press the
The air conditioner runs in HEAT mode.
button.
Note
You can change modes at any time.
3
To adjust the temperature, press the
button one or more times
until the required temperature is displayed.
Possible temperatures are between 16°C and 30°C inclusive.
Result: ◆ Each time you press the button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts heating, provided that the room
temperature is lower than the desired temperature
(selected temperature+3°C).
◆ If the room temperature reaches the set temperature, the air
conditioner stops heating, but the fan is still operating.
4
Select the fan speed by pressing the
until the required setting is displayed:
button one or more times
)
Automatic (rotated :
Low
Medium
High
Result:
◆
◆
Each time you press the
button, the indoor unit beeps.
For the first three to five minutes, the fan operates very
slowly until the air has been sufficiently warmed. Once the
correct temperature has been reached, the fan is automatically
set to the required speed.
5
To control the direction of the air flow, refer to pages 16 and 17.
E-11
Changing the Room Temperature Quickly
The Turbo cooling/heating function is used to cool or heat your room as
quickly as possible.
Example : You have just come home and find that the room is very
hot. You wish to cool it down as quickly as possible.
The Turbo function operates for 30 minutes with the maximum settings before
returning automatically to the mode and temperature previously selected.
1
If necessary, press the
(On/Off) button.
Result:
◆ The operation indicator on the indoor unit lights up.
◆ The air conditioner starts up in the mode selected when the unit
was last used.
◆ The indoor unit beeps.
2
Press the
Result:
button.
◆ The temperature and fan settings are adjusted automatically.
◆ The air conditioner cools or heats the room as quickly as possible.
◆ After 30 minutes, the air conditioner is reset automatically to the
previous mode, temperature and fan settings.
But, if you press the
button in DRY or FAN mode,
it will change to AUTO mode automatically.
3
4
If you wish to stop the Turbo function before the end of the 30-minute period,
press the
button one or more times until
or
disappears.
Result:
The air conditioner is reset automatically to the previous mode,
temperature and fan settings.
To control the direction of the air flow, refer to pages 16 and 17.
E-12
Removing Excess Humidity
If the atmosphere in your room is very humid or damp, you can
remove excess humidity without lowering the room temperature too
much.
1
If necessary, press the
(On/Off) button.
Result: The operation indicator on the indoor unit lights up.
◆
◆ The air conditioner starts up in the mode selected when
the unit was last used.
◆ The indoor unit beeps.
IMPORTANT
The air conditioner is fitted with a protection mechanism
to prevent the unit from being damaged when it is started
immediately after being:
◆ Plugged in
◆ Stopped
It will start up normally after three minutes.
2
If the
is not displayed at the top of the remote control, press the
button on the remote control one or more times until it appears.
Result:
◆
◆
The indoor unit beeps each time you press the
The air conditioner runs in DRY mode.
button.
Note
You can change modes at any time.
3
To adjust the temperature, press the
button one or more times
until the required temperature is displayed.
Possible temperatures are between 18°C and 30°C inclusive.
Result: ◆ Each time you press the button:
- The temperature is adjusted by 1°C
- The indoor unit beeps
◆ The air conditioner starts removing the excess humidity;
the quantity of air is adjusted automatically.
4
To control the direction of the air flow, refer to pages 16 and 17.
E-13
|