Roland Music Mixer RE 20 User Guide

Thank you, and congratulations on your choice of the BOSS RE-20 Space Echo.  
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY”  
and “IMPORTANT NOTES” (separate sheet).  
These sections provide important information concerning the proper operation of the unit.  
Additionally, in order to feel assured that you have gained a good understanding of every  
feature provided by your new unit, this manual should be read in its entirety. The manual  
should be saved and kept on hand as a convenient reference.  
Main Features  
The RE-20 uses COSM technology to faithfully simulate the characteristics of the famed  
Roland SPACE ECHO RE-201.  
Faithfully reproduces the characteristics of the RE-201, including the echo’s distinctive wow-  
and flutter-induced wavering and the compressed sound obtained with magnetic saturation.  
The Mode Selector carries on the tradition of the RE-201, offering twelve different  
reverberation effects through various combinations of the three playback heads and reverb.  
You can set delay times with the TAP input pedal and use an expression pedal (sold  
separately) for controlling parameters.  
Equipped with a “Virtual Tape Display,” which produces a visual image of a running tape.  
About COSM (Composite Object Sound Modeling)  
Composite Object Sound Modeling—or “COSM” for short—is  
BOSS/Roland’s innovative and powerful technology that’s used  
to digitally recreate the sound of classic musical instruments and  
effects. COSM analyzes the many factors that make up the original  
sound—including its electrical and physical characteristics—and  
creates a digital model that accurately reproduces the original.  
Copyright © 2007 BOSS CORPORATION  
All rights reserved. No part of this publication may be reproduced in  
any form without the written permission of BOSS CORPORATION.  
 
 
Panel Descriptions  
Front Panel  
REVERB VOLUME Knob  
Adjusts the volume of the reverb.  
Turning the knob to the right increases the volume  
of the reverb.  
TREBLE Knob  
Adjusts the echo’s high-frequency range.  
The frequency response is flat when the  
knob is at the center position; turning  
the knob to the right (clockwise) boosts  
the high frequencies, while turning it to  
the left cuts the high frequencies.  
MODE SELECTOR Knob  
Turn to select one of the twelve  
combinations of echo and reverb (p. 18).  
BASS Knob  
Adjusts the echo’s  
low-frequency range.  
The frequency response  
is flat when the knob is  
at the center position;  
turning the knob to the  
right (clockwise) boosts  
the low frequencies,  
while turning it to the  
left cuts the low  
PEAK LEVEL Indicator  
This lights when signal  
reaches the level at which the  
input sound starts to distort.  
*
This also lights when the  
intensity is increasing and  
when the echo sound  
oscillates while the twist  
effect is being applied.  
frequencies.  
INPUT VOLUME Knob  
Adjusts the input levels for  
Inputs A and B.  
REPEAT RATE Knob  
This adjusts the intervals between  
echoes. The spacing between the  
echoes is reduced as the knob is  
turned further to the right.  
*
You can adjust the input level  
with the INPUT VOLUME  
knob regardless of whether the  
effect is switched on or off.  
*
The ranges for the speed rate  
setting differ in Normal mode and  
Long mode (p. 15).  
ECHO VOLUME Knob  
Adjusts the volume of the echo.  
The volume of the echo sounds increases  
as the knob is turned further to the right.  
INTENSITY Knob  
This adjusts the volume of the echo repeat sound (the feedback  
volume). The volume of the feedback increases as the knob is  
turned further to the right. With certain sounds and knob settings,  
you can also produce oscillation.  
3
 
   
Panel Descriptions  
POWER Indicator  
This indicator shows whether the power is on or off, and also functions as a battery-check indicator.  
*
When the indicator starts to dim or fails to light, the batteries are exhausted. When this occurs, install  
new batteries. For instructions on replacing the batteries, refer to “Installing Batteries” (p. 6).  
TAP Indicator  
This flashes in time with the delay  
time set by the tap input.  
EFFECT ON/OFF Indicator  
This lights up when the effect is on.  
*
The light is turned off when the twist  
effect is applied.  
TAP Pedal  
EFFECT ON/OFF Pedal  
You can set the delay time (tap  
delay time) by briefly depressing  
this pedal at the desired tempo (tap  
input). Also, you can obtain the  
“twist” effect by keeping the pedal  
depressed (p. 14).  
This alternately switches the effect on  
or off each time the pedal is pressed.  
Even when the effect is switched off,  
the echo sounds still fade gradually.  
*
Turning up the INTENSITY knob  
causes the echo sounds to continue.  
*
The maximum values that can be set  
for the tap delay time in Normal/  
Long mode and Variation mode  
differ (p. 18).  
Virtual Tape Display  
The movement of the light provides a visual  
image resembling a running tape.  
The movement of the light is synchronized to  
the virtual tape speed.  
4
 
Panel Descriptions  
Rear Panel  
INPUT Jacks  
EXP Pedal Jack  
(INPUT A/MONO, B)  
Connect an optional expression pedal (such as the  
Roland EV-5) to this jack.  
These input jacks are used for  
connecting electric guitars, keyboards,  
other instruments, and effects  
processors.  
Connect mono instruments or effects to  
the A/MONO jack.  
Once connected, the pedal can be used to control  
the repeat rate and intensity in real time.  
“Control Using an Expression Pedal” (p. 16)  
“Making the Connections” (p. 7)  
*
The A/MONO jack also doubles as the  
power switch. The power comes on when a  
plug is inserted into the A/MONO jack,  
and goes off when it is unplugged.  
Unplug any connected cords when the  
unit is not in use.  
DIRECT Switch  
This switches the direct sound on and off.  
If you want to turn off output of the  
direct sound, set the DIRECT switch  
to OFF.  
DC IN (AC Adaptor)  
Jack  
This jack is for connecting an  
AC adaptor (BOSS PSA series,  
sold separately).  
Using an AC adaptor makes  
possible long performances  
without worrying about your  
batteries going dead.  
OUTPUT Jacks  
(OUTPUT A/MONO, OUTPUT B)  
Use these jacks to connect the RE-20 to a guitar  
amp, a keyboard amp, or to an effects  
processor, mixer, multitrack recorder, or other  
such device.  
*
When you are using an AC  
adaptor, be sure to use only the  
specified type (PSA series).  
Using an adaptor other than  
the specified type may cause  
the unit to malfunction, or  
cause damage to the unit.  
When connected to both A/MONO and B, a ste-  
reo effect can be obtained when reverb is applied.  
If you are using the RE-20 in mono, connect to  
the A/MONO jack only.  
“Making the Connections” (p. 7)  
5
 
 
Installing Batteries  
Insert the batteries as shown below, being careful to orient the batteries correctly.  
fig.010  
• When turning the unit upside-down, get a bunch of newspapers or magazines, and  
place them under the four corners or at both ends to prevent damage to the buttons  
and controls. Also, you should try to orient the unit so no buttons or controls get  
damaged.  
• When turning the unit upside-down, handle it with care to avoid dropping it, or  
allowing it to fall or tip over.  
• Make sure the “+” and “–” ends of the batteries are oriented correctly.  
• Batteries are supplied with the unit. The life of these batteries may be limited,  
however, since their primary purpose is to enable testing.  
• When the batteries run down, the POWER indicator grows dim. If this happens, install  
with new batteries.  
• When replacing the batteries, use six AA type batteries.  
• Avoid using new batteries together with used ones. In addition, avoid mixing different  
types of batteries. Doing so can result in fluid leakage.  
• Battery life can vary depending on battery type.  
Continuous usage time under battery power is about 32 hours with alkaline batteries  
and about 9 hours with carbon batteries. (This may vary according to usage  
conditions.)  
6
 
   
Making the Connections  
• When using an AC adaptor, be sure to use only the specified type (PSA series; sold  
separately).  
Using an adaptor other than the specified type may cause the unit to malfunction, or  
cause damage to the unit.  
• To prevent malfunction and/or damage to speakers or other devices, always turn  
down the volume and turn off the power to all devices before making any connections.  
• Noise may be produced if wireless communications devices, such as cell phones, are  
operated in the vicinity of this unit. Such noise could occur when receiving or initiating  
a call, or while conversing. Should you experience such problems, you should relocate  
such wireless devices so they are at a greater distance from this unit, or switch them  
off.  
• Some connection cables contain resistors. When connection cables with resistors are  
used, the sound level may be extremely low, or impossible to hear. For information on  
cable specifications, contact the manufacturer of the cable.  
• The INPUT A/MONO jack doubles as a power switch. Inserting a plug in the INPUT  
A/MONO jack turns on the power; the power is switched off when the plug is  
disconnected. Be sure to unplug the cable from this jack when the RE-20 is not in use.  
• If there are batteries in the unit while an AC adaptor is being used, normal operation  
will continue should the line voltage be interrupted (power blackout or power cord  
disconnection).  
• Once the connections have been completed, turn on power to your various devices in  
the order specified. By turning on devices in the wrong order, you risk causing  
malfunction and/or damage to speakers and other devices.  
When powering up:  
Turn on the power to your guitar amp last.  
When powering down: Turn off the power to your guitar amp first.  
• Always make sure to have the volume level turned down before switching on power.  
Even with the volume all the way down, you may still hear some sound when the  
power is switched on, but this is normal, and does not indicate a malfunction.  
• When operating on battery power only, the POWER indicator will become dim when  
battery power gets too low. Replace the batteries as soon as possible.  
• This unit is equipped with a protection circuit. A brief interval (a few seconds) after power-  
up is required before the unit will operate normally.  
7
 
   
Making the Connections  
Mono Output Connection  
fig.020  
AC Adaptor  
PSA series  
(sold separately)  
Electric Guitar  
or  
Guitar Amplifier  
or  
Keyboard  
MTR  
Mixer  
fig.030  
8
 
 
Making the Connections  
Stereo Output Connection  
Mono Input  
fig.060  
AC Adaptor  
PSA series  
(sold separately)  
Electric Guitar  
Guitar Amplifier  
or  
or  
Keyboard  
MTR  
Mixer  
Stereo Input  
fig.070  
AC Adaptor  
PSA series  
(sold separately)  
Guitar Amplifier  
or  
Effector + Electric Guitar  
or  
MTR  
Mixer  
Keyboard  
9
 
 
Making the Connections  
Connecting to SEND/RETURN  
With Guitar Amps  
Mono Send/Mono Return  
fig.060  
AC Adaptor  
PSA series  
(sold separately)  
SEND  
RETURN  
Guitar Amplifier  
Electric Guitar  
Mono Send/Stereo Return  
fig.070  
AC Adaptor  
PSA series  
(sold separately)  
RETURN R  
RETURN L  
SEND  
Guitar Amplifier  
Electric Guitar  
10  
 
   
Making the Connections  
Connecting to an MTR or Mixer  
If you want to turn off output of the direct sound—for example when connecting to a  
mixer’s SEND/RETURN—set the DIRECT switch to OFF.  
Mono Send/Mono Return  
fig.060  
Set DIRECT  
switch to OFF  
AC Adaptor  
PSA series  
(sold separately)  
SEND  
RETURN  
MTR  
Mixer  
Stereo Send/Stereo Return  
fig.070  
Set DIRECT  
switch to OFF  
AC Adaptor  
PSA series  
(sold separately)  
RETURN R  
RETURN L  
SEND R  
SEND L  
MTR  
Mixer  
11  
 
   
Operating the RE-20  
Basic Operation  
For this demonstration of using the pedals, first press the EFFECT ON/OFF pedal to  
switch on the effect (ON/OFF indicator lit), and set the DIRECT switch to ON.  
fig.080  
1
2
3
9
4
5
6
7
8
1. Set the knobs as shown in the figure.  
8
2. Using the INPUT VOLUME knob  
device, adjust the input level so that the PEAK LEVEL indicator  
momentarily when the instrument connected to the RE-20 is played forcefully.  
and the volume control on the connected  
9
lights  
7
3. Set the MODE SELECTOR knob  
to the 1 position.  
to adjust the volume of the echo.  
4
5. Turn the REPEAT RATE knob  
to adjust the echo interval.  
5
6. Turn the INTENSITY knob  
to adjust the volume of the echo’s repeat.  
1
7. Turn the BASS knob  
to adjust the echo’s low-frequency range.  
2
8. Turn the TREBLE knob  
to adjust the echo’s high-frequency range.  
7
9. Set the MODE SELECTOR knob  
to the REVERB ONLY position.  
3
10. Turn the REVERB VOLUME knob  
to adjust the volume of the reverb.  
to select the Variation mode.  
7
11. Turn the MODE SELECTOR knob  
*
For more detailed information on the Variation mode types, refer to the “About the Variation Mode”  
(p. 18).  
12  
 
   
Operating the RE-20  
Adjusting the Input  
Volume  
Adjusting the Volume of  
the Echo’s Repeat  
The input level can be adjusted with the  
8
INPUT VOLUME knob  
.
5
INTENSITY knob  
.
*
The input level can be adjusted with the  
INPUT VOLUME knob regardless of  
whether the effect is switched on or off.  
Adjusting the Tone of the  
Echo (BASS, TREBLE)  
Switching the Echo and  
Reverb Variations  
1
2
You can use the BASS  
and TREBLE  
knobs to adjust the low- and high-frequency  
ranges of the echo sound only.  
7
YoucanusetheMODESELECTORknob  
to switch among the twelve Variation modes,  
which offer different combinations of echo  
and reverb.  
Adjusting the Volume of  
the Reverb Sound  
*
For more detailed information on the  
Variation mode types, refer to the “About  
the Variation Mode” (p. 18).  
You can adjust the volume of the reverb  
3
sound with the REVERB VOLUME knob  
.
*
Enabled only when the MODE SELECTOR  
knob is set to any position from 5 through 11  
or to REVERB ONLY.  
Adjusting the Volume of  
the Echo Sound  
You can adjust the volume of the echo sound  
6
with the ECHO VOLUME knob  
.
Adjusting the Echo  
Interval  
You can adjust the amount of time between  
4
echoes with the REPEAT RATE knob  
.
13  
 
             
Operating the RE-20  
Setting the Delay Time with the TAP Pedal  
(Tap Delay Time)  
1. Using the MODE SELECTOR knob, select the Variation mode for which the tap  
delay time is to be set.  
*
For more on the playback heads for which the tap delay time is set, and the maximum values of the  
settings, refer to “About the Variation Mode” (p. 18).  
2. Press the TAP pedal two or more times at the tempo you want to set.  
This sets the tap delay time. The TAP indicator flashes in sync with the tap delay time.  
Blink  
Press two or more times  
*
*
Enabled only when the MODE SELECTOR knob is set to any position from 1 through 11.  
When any of the following are carried out, the tap delay time setting changes  
REPEAT RATE knob turned ➔  
changes to the value set with the REPEAT RATE knob  
changes to the value set with the REPEAT RATE knob  
MODE SELECTOR knob turned ➔  
Repeat rate or twist changed with changes to the value set with the expression pedal  
an expression pedal  
*
*
You cannot save the tap delay time setting.  
When the twist effect is applied using the TAP pedal (from when the TAP indicator is off to when it  
goes on or starts flashing), you cannot set the tap delay time.  
Applying the Twist Effect with the TAP Pedal  
The twist effect simultaneously increases the repeat rate and the intensity, causing the  
echo sound to oscillate. In addition, the echo volume level is controlled.  
*
Enabled only when the MODE SELECTOR knob is set to any position from 1 through 11.  
1. Press and hold down the TAP pedal.  
The TAP indicator goes out, and application of the twist effect begins.  
The echo sound begins to oscillate, then the oscillation increases as the pitch rises as well.  
Off  
Press and hold down  
*
You cannot set the repeat rate and intensity while the TAP pedal is held down.  
14  
 
     
Operating the RE-20  
2. Release the TAP pedal.  
The pitch of the oscillating sound starts to fall, and the original echo sound returns.  
The TAP indicator lights when the twist effect is finished.  
*
Once the TAP pedal is released, changing the repeat rate or intensity cancels the twist effect. The  
setting is then changed to the value set with the knob or expression pedal.  
*
*
Adjusting the MODE SELECTOR knob while the twist effect is being applied cancels the twist effect.  
You can apply the twist effect with an external expression pedal. For more detailed information, refer to  
“Control Using an Expression Pedal” (p. 16).  
Switching the Repeat Rate and Delay Time Mode  
The RE-20 features two modes to select from.  
Normal mode:  
The REPEAT RATE knob functions over the same range as the  
RE-201. Additionally, the maximum value that can be set for  
the tap delay time is three seconds (when the MODE  
SELECTOR knob is set to the 3 or 7 position).  
Long mode:  
The range for the REPEAT RATE knob setting is expanded to  
twice the normal setting. Additionally, the maximum value  
that can be set for the tap delay time is six seconds (when the  
MODE SELECTOR knob is set to the 3 or 7 position).  
1. Turn off the RE-20.  
*
Disconnecting the plug from the INPUT A/MONO jack switches off the power.  
2. While holding down the TAP pedal, turn on the power to the RE-20.  
The virtual tape display flashes, and then remains lit.  
*
Connecting the plug to the INPUT A/MONO jack switches on the power.  
3. Confirm that the virtual tape display is lit, then release the TAP pedal.  
4. Turn the MODE SELECTOR knob to select the mode.  
MODE  
Mode  
SELECTOR  
1
2
Normal mode  
Long mode  
5. Press the TAP pedal.  
The TAP indicator flashes rapidly, and the setting is saved to the RE-20’s memory.  
When the setting is saved, the TAP indicator remains lit, and the RE-20 returns to its  
normal operating status.  
*
*
*
Be sure not to turn off the power while the TAP indicator is flashing rapidly.  
This setting is saved even after the power is turned off.  
When the RE-20 is set to Long mode, the EFFECT ON/OFF indicator and TAP indicator flash rapidly  
immediately after the power is turned on.  
*
The default factory setting is Normal mode.  
15  
 
   
Operating the RE-20  
Control Using an Expression Pedal  
You can control the following functions with an expression pedal (Roland EV-5; sold  
separately) connected to the EXP PEDAL jack on the rear panel.  
REPEAT RATE: The echo interval becomes shorter as the toe of the expression  
pedal is pressed further.  
In Long mode, the range for the Repeat Rate setting is twice that of  
Normal mode.  
INTENSITY:  
The Intensity increases as the toe of the expression pedal is pressed  
further, increasing the volume of the echo repeat sound (the  
feedback volume).  
ECHO LEVEL:  
This controls the level input to the echo. The volume of the echo  
sounds increases as the toe of the expression pedal is pressed further.  
* This function can be controlled only with an expression pedal.  
* The input level to the reverb is not changed.  
TWIST:  
Repeat Rate and Intensity are controlled simultaneously.  
In addition, this controls the ECHO VOLUME according to the  
echo level.  
As you further press down on the toe of the expression pedal, the  
echo sound starts to oscillate, then the oscillation rate increases  
and the pitch of the oscillation sound rises.  
The Repeat Rate and Intensity are set to the minimum value when the heel of the pedal  
is pressed down; when you press firmly on the toe of the pedal, the value changes to  
the value that’s been set with the knob.  
With the twist effect, the value that’s been set with the knob is obtained when the heel  
of the pedal is pressed down; when you press firmly on the toe of the pedal, the value  
changes to the maximum value.  
Expression pedal  
(Roland EV -5, etc.)  
*
Use only the specified expression pedal (Roland EV-5; sold separately). By connecting any other  
expression pedals, you risk causing the unit to malfunction and/or damage to the unit.  
16  
 
   
Operating the RE-20  
Setting the Function of the Expression Pedal  
1. Turn off the RE-20.  
*
Disconnecting the plug from the INPUT A/MONO jack switches off the power.  
2. While holding down the TAP pedal, turn on the power to the RE-20.  
The virtual tape display flashes, and then remains lit.  
*
Connecting the plug to the INPUT A/MONO jack switches on the power.  
3. Turn the MODE SELECTOR knob to select a function for the expression pedal.  
MODE  
Function  
SELECTOR  
3
4
5
6
REPEAT RATE  
INTENSITY  
ECHO LEVEL *1  
TWIST  
*1 This function can be controlled only with an expression pedal.  
4. Press the TAP pedal to set that function.  
The TAP indicator flashes rapidly, and the setting is saved to the RE-20’s memory.  
When setting is saved, the TAP indicator remains lit, and the RE-20 returns to its  
normal operating status.  
*
*
*
Be absolutely sure to avoid turning off the power while settings are being saved.  
This setting is retained even while the power is turned off.  
The factory default setting is REPEAT RATE.  
17  
 
 
About the Variation Mode  
You can use the MODE SELECTOR knob to switch among the twelve Variation modes,  
which offer different combinations of echo and reverb.  
REPEAT  
REVERB ECHO  
MODE  
SELECTOR  
REVERB  
ONLY  
1
2
3
4
5
6
7
8
9
10 11  
1
Play-  
back  
Heads  
2
3
REVERB  
:
:
On  
The playback heads set with the tap delay times  
REPEAT (MODE SELECTOR knob “1”–“4”)  
:
Echo only  
REVERB ECHO (MODE SELECTOR knob “5”–“11”) : Combined echo and reverb  
REVERB ONLY (MODE SELECTOR knob “REVERB ONLY”) : Reverb only  
About the Playback Heads  
Relative to whatever the tap delay time is at playback head 1, the tap delay time at  
playback head 2 is twice that, and the tap delay time at playback head 3 is three times  
that.  
Example: With the MODE SELECTOR knob set to the “11” position and the tap  
delay time set to 0. 5 seconds  
The setting is 0.5 seconds at playback head 1, 1 second at playback head 2, and 1.5  
seconds at playback head 3.  
*
The maximum values that can be set for the tap delay time in Normal/Long mode and Variation mode  
differ.  
Maximum Values for Tap Delay Time (Seconds)  
MODE  
SELECTOR  
Normal Mode  
Long Mode  
1, 5, 8, 10, 11  
2, 4, 6, 9  
3, 7  
1
2
3
2
4
6
18  
 
       
About the Roland SPACE ECHO RE-201  
The Roland SPACE ECHO RE-201 is a reverb-equipped tape echo that debuted in 1974.  
About the Configuration of the Tape Echo/Reverb  
The tape echo section features an erase head, record head, and three playback heads  
arranged sequentially at equal intervals, such that a sound is played back three times  
at equal intervals.  
The three playback heads are switched with the MODE SELECTOR knob, making it  
possible to create different variations (patterns) of echo intervals.  
The reverb section is equipped with a spring reverb. The reverb signal path is  
connected in parallel to the tape echo section.  
Changing of the Echo Sound’s Pitch When  
REPEAT RATE is Changed  
Turning the REPEAT RATE knob to the right (clockwise) gradually increases the tape  
speed. As this happens, sounds are played back more closely together, and the pitch  
begins to rise.  
Simultaneously, the density of the sounds during recording gradually decreases, so  
when those sounds reach the playback heads, the pitches that were raised then begin  
to fall.  
Oscillation in the Tape Speed  
Even without any change in the REPEAT RATE knob setting, the tape speed is always  
changing slightly due to the resistance from mechanical friction, tape slippage, and  
other factors.  
This creates oscillations in the pitch of each of the three echo sounds, automatically  
producing the RE-201’s characteristic chorus effect.  
About the Change in Sound Quality with Magnetic Saturation  
Due to magnetic saturation, recording to and playing back from tape produces a sense  
of compression in the sound, giving it a characteristic warmth that is unique to tape.  
In addition, the sonic quality of playback and recording also changes with the change  
in tape speed.  
About the Reverb  
The RE-201’s reverb section includes three springs arranged in a “Z” formation. The  
vibration of each spring influences the motion of the others to produce the reverb’s  
characteristic sound.  
19  
 
 
Troubleshooting  
Power doesn’t come on  
Is the guitar or keyboard connected correctly  
to the INPUT A/MONO jack?  
Are the INTENSITY knob and INPUT  
VOLUME knob positioned correctly?  
Check the connections again (p. 7–p. 11).  
Sounds may become distorted with the knob at  
certain settings. Turn down the INTENSITY  
knob and INPUT VOLUME knob to an  
appropriate level. If in spite of these measures  
the sound is still distorted, lower the output  
level of the device connected to the INPUT jacks.  
*
The power will not turn on without a plug  
connected to the INPUT A/MONO jack.  
Have the batteries run down?  
Replace them with new batteries (p. 6).  
*
The batteries included with the RE-20 are meant only  
to confirm that the unit is functional at the factory.  
Echo sounds not cancelled even  
when effect is switched off  
*
To reduce battery consumption, be sure to  
disconnect the plug connected to the INPUT A/  
MONO jack whenever the unit is not in use.  
Do you have a long delay time set?  
Try turning the ECHO VOLUME knob  
completely to the left (counterclockwise); this  
allows you to cancel the continuing sounds.  
Is the specified AC adaptor (PSA series; sold  
separately) connected correctly?  
Never use any AC adaptor other than the  
adaptor specified.  
Is the Intensity turned up?  
Try turning the INTENSITY knob or ECHO  
VOLUME knob completely to the left  
(counterclockwise); this allows you to cancel  
the continuing sounds.  
No sound/Volume is low  
Sounds output even with no  
sound input  
Is the other equipment connected correctly?  
Check the connections again (p. 7–p. 11).  
Is the Intensity setting turned up?  
With higher Intensity settings, even when no  
sounds are being input, the repeat sound  
in the sound may occur.  
Could the INPUT VOLUME knob, REVERB  
VOLUME knob or ECHO VOLUME knob be  
turned down?  
Use the INPUT VOLUME knob, REVERB knob  
or ECHO VOLUME knob to raise the input level.  
Set the INTENSITY knob at some point to the  
left of the center position.  
Is the volume turned down on the connected  
guitar/keyboard, effects processor, or other device?  
Check the settings on the connected equipment  
(p. 7–p. 11).  
Can’t set tap delay time  
Are you sure the tap input you supplied was within  
the range that can be set for the tap delay time?  
The maximum values that can be set for the tap  
delay time in Normal/Long mode and  
Variation mode differ (p. 18).  
Is the DIRECT switch off?  
Only the effect sound is output when the  
DIRECT switch is set to OFF. To output the  
direct sound, set the switch to ON.  
The volume level of the  
instrument connected to the  
INPUT jack is too low  
Could the connected expression pedal be in  
the raised position?  
Could you be using a connection cable that  
When ECHO LEVEL is assigned as the function  
of the expression pedal, no echo sound is  
output unless you step on the pedal (p. 16).  
contains a resistor?  
Use a connection cable that does not contain a  
resistor.  
20  
 
 
Sample Settings  
AMBIENCE  
This sound adds a sense of  
space using a short delay and  
reverb.  
RICH ECHO  
This is a sumptuous sound  
with a rich reverb added to  
the delay. This produces an  
even greater effect when  
played back in stereo.  
MULTI SLAP  
Effective with muting  
techniques for giving the  
sound a prominent contour.  
This is even more effective  
with phrases timed to the  
repeat sound.  
SPACE  
Connecting an expression  
pedal and using the pedal to  
control the intensity in real  
time allows you to produce  
even more fantastic sounds.  
To make this setup effective,  
set the INTENSITY knob at a  
position between three  
o’clock and maximum.  
21  
 
 
Main Specifications  
RE-20: Space Echo  
Power Supply  
DC 9 V: Dry battery LR6/R6 (AA) type x 6,  
AC Adaptor (PSA series)  
Nominal Input Level  
-20 dBu (INPUT VOLUME knob: center),  
max +4 dBu  
Current Draw  
75 mA (9 V max.)  
Input Impedance  
* Expected battery life under continuous use:  
Carbon: 9 hours  
Alkaline: 32 hours  
These figures will vary depending on the  
actual conditions of use.  
1 MΩ  
Nominal Output Level  
-20 dBu  
Output Impedance  
1 kΩ  
Dimensions  
Recommended Load Impedance  
173 (W) x 158 (D) x 57 (H) mm  
6-13/16 (W) x 6-1/4 (D) x 2-1/4 (H) inches  
10 kΩ or greater  
Weight  
Display  
1.2 kg / 2 lbs 11 oz (including batteries)  
Virtual Tape Display  
Accessories  
Controls  
Owner’s Manual  
EFFECT ON/OFF pedal  
TAP pedal  
BASS knob  
Leaflet (“USING THE UNIT SAFELY,”  
“IMPORTANT NOTES,” and “Information”)  
Dry battery R6 (AA) type (carbon) x 6  
TREBLE knob  
REVERB VOLUME knob  
REPEAT RATE knob  
INTENSITY knob  
ECHO VOLUME knob  
MODE SELECTOR knob  
INPUT VOLUME knob  
DIRECT switch  
Options  
AC Adaptor (PSA series)  
Expression pedal (Roland EV-5)  
* 0 dBu = 0.775 Vrms  
*
In the interest of product improvement, the  
specifications and/or appearance of this unit are  
subject to change without prior notice.  
Indicators  
POWER indicator  
(serves also as battery check indicator)  
PEAK LEVEL indicator  
EFFECT ON/OFF indicator  
TAP indicator  
Connectors  
INPUT jacks A/MONO, B (1/4 inch phone type)  
OUTPUT jacks A/MONO, B (1/4 inch phone type)  
EXP PEDAL jack (1/4 inch TRS phone type)  
DC IN jack (DC 9 V)  
22  
 
 
For EU Countries  
UK  
DE  
FR  
IT  
ES  
PT  
NL  
DK  
NO  
SE  
FI  
HU  
PL  
CZ  
SK  
EE  
LT  
LV  
SI  
GR  
 
For EU Countries  
For the USA  
This product complies with the requirements of European Directive 89/336/EEC.  
FEDERAL COMMUNICATIONS COMMISSION  
RADIO FREQUENCY INTERFERENCE STATEMENT  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the  
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in  
a
residential  
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee  
that interference will not occur in  
a
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received, including interference that may cause undesired operation.  
Unauthorized changes or modification to this system can void the users authority to operate this equipment.  
This equipment requires shielded interface cables in order to meet FCC class B Limit.  
For Canada  
NOTICE  
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.  
AVIS  
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.  
G6027121R1  
 

Remington Trimmer HC 810, HC 815, HC 8017, HC 912, HC 920, HC 921, HC 930, G03 038 User Guide
Rockford Fosgate Stereo Amplifier PUNCH 4020 DSM User Guide
Roland Musical Instrument HP 1 User Guide
Salton Ultrasonic Jewelry Cleaner JW10 User Guide
Samsung Blu ray Player 01963B User Guide
Samsung Cell Phone GH68 02493A User Guide
Samsung Indoor Furnishings WE357A0C User Guide
Samsung Microwave Oven SMH9187 User Guide
Sanyo Air Conditioner 07AHX52 User Guide
Sanyo Microcassette Recorder TRC 6040 User Guide